Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
Do you find yourself searching for critical information on How to Install a Bathtub?
Installing a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately challenging task. If the old bathtub is conveniently accessible, the project can relocate speedily; if you need to open up a wall to remove the old bathtub as well as position the brand-new tub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Make certain you have actually qualified on your own for the job as well as are comfortable trying it. Rather than employing a professional to take control of a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This write-up will aid you install a brand-new bath tub in your shower room if you have actually already gotten a new bathtub and don't require to transform the plan of your previous water supply pipes.
Your devices and product list should make up the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, then the first thing you need to do is detach the water system. After doing so, turn on the taps to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be fairly bothersome due to the restricted access that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin ensuring that the washing machines are in area between the tap and the sink. Protect the faucet in place with the producer given backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap ports. The former kind needs to be connected to the faucet ends initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, position the bathtub in the needed position. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub up until the level checks out degree.
To set up faucets, fit the bottom of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the same for the other faucet.
Turn on the water system and also check all joints as well as new pipework for leaks and tighten them if necessary. Fill the tub as well as likewise inspect the overflow outlet and the regular outlet for leaks.
Finally, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub must wait up until the tub has been used at least once as this will resolve it into its final placement.
Planning for the Installation
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its final position.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, triggering the water to penetrate the wall surface in between the bathroom and also the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can split relatively early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly readily available on the market. It is suggested to fit the tiles utilizing water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I am hoping you liked our blog post. In case you appreciated our page kindly do not forget to share it. I am grateful for your time. Visit us again soon.
Immediate relief, just a call. Report this page